Retrobriting a yellowed Super Famicom shell without wrecking the labels
Symptom The upper shell has turned from grey to a deep yellow or brown, unevenly, with darker patches where the plastic was exposed to more light.
The yellowing is caused by a brominated flame retardant in the ABS plastic reacting with ultraviolet light and oxygen. It is reversible with hydrogen peroxide and UV, but the treatment is not permanent and it is easy to damage the parts of the shell you cannot replace, like the printed logos and the molded texture.
Why it yellows and why it comes back
The flame retardant is mixed into the plastic, not applied to the surface, so the yellowing goes all the way through rather than sitting on top. That is why sanding and polishing do not fix it; you remove a millimetre of plastic and the colour underneath is the same.
The treatment reverses the chemical reaction on the surface, and the same reaction will start again the moment the shell is exposed to UV. Treated shells typically re-yellow over two to five years. That is a useful thing to tell the owner before taking the job, because it is not a permanent restoration.
Deciding whether to treat it
Test a small area first, on the inside of the shell where nobody will see it. Apply the same concentration of peroxide you plan to use for the same time, and check the result. Different production runs of ABS respond differently and some will only lighten a little no matter what you do.
Check the printed areas before you start. The red and white logos on a Super Famicom shell are paint, not molded plastic, and peroxide will lift them if the concentration is high or the soak is long. If the logos are already fragile, mask them with vinyl film or accept that they will fade.
- Test on an internal surface with the concentration and duration you plan to use.
- Inspect every printed area and the molded texture, and note anything already damaged.
- Clean the shell thoroughly with warm water and dish soap before treatment. Dirt and grease block the peroxide.
- Check the metal inserts and the screw bosses for corrosion, since those will also be exposed to the liquid.
- Decide whether the job is worth it. A shell that is only slightly yellowed may not be worth the risk of a botched treatment.
Peroxide, UV and patience
Use 3 to 12 percent hydrogen peroxide as a gel, brushed on and covered with clear plastic film so it does not dry out. Higher concentrations work faster and attack the plastic and the paint faster too. For a first attempt, 6 percent for six to eight hours of bright sunlight is a reasonable balance.
Keep the shell wet with peroxide the whole time. A patch that dries out will stop reacting and can end up lighter or darker than the rest of the shell. Turn the shell every hour and re-brush any area that looks dry. If the day is cloudy the reaction will be very slow and uneven, so wait for a bright day rather than doubling the concentration.
- Disassemble the console completely and wash the shell parts with warm water and dish soap. Rinse and dry fully.
- Apply 6 percent peroxide gel in an even coat and cover with clear plastic film.
- Place in direct sunlight for six to eight hours, turning every hour and re-wetting any dry patches.
- Check progress after four hours. Stop when the colour matches, not when it is white, because over-treatment makes the plastic brittle.
- Rinse thoroughly with clean water for several minutes and dry completely before reassembly.
- Protect the treated shell with a UV-blocking clear coat if the owner wants the result to last longer, and tell them the yellowing will return eventually.
Fault tree branches
where this symptom also leadsIf: The shell is cracked as well as yellowed
Treat the plastic and deal with the crack at the same time so the console is only dismantled once.
GBA SP cracked hinge: replacing the shell without breaking the ribbonIf: The metal parts are corroded as well
Clean the metalwork while the shell is apart, since corrosion spreads back into the plastic.
Top loader with green fur on the contacts: cleaning a corroded 72-pin slotIf: The cartridge slot is dirty and the shell is going to be off anyway
Service the slot at the same time.
Super Famicom: bent pins in the 62-pin slot after a cartridge was forced in