Skip to content
Revamp Bench复活台 · revamp.top
bench records · filed weekly 中文

PC Engine recap: weak video, humming audio and a console that only works cold

Symptom Picture is washed out or rolls, audio hums badly, RF output is worse than composite, or the console needs several minutes to warm up before it will run.

Console
NEC PC Engine PI-TG001
Board
TG-01
Generation
PC Engine
Class
No power
Difficulty
4 / 5 · Advanced
Bench time
2 h
Success rate
4 in 5
Filed
29 October 2026
TG-01 board fault location drawing, highlighted parts C101, C107, VR101, IC102
Fig. 1 · TG-01 — amber marks the faulted part (C101, C107, VR101, IC102)

Every PC Engine is now well past the point where its electrolytic capacitors were expected to last. The symptoms are easy to mistake for a dying chip, which is why consoles get written off when a recap would have restored them completely. The good news is that this is one of the most straightforward recaps in retro hardware.

Symptom

Symptoms that are electrical rather than logical

A console whose faults change with temperature is telling you about its capacitors, not its chips. Silicon fails in ways that are consistent, and electrolytic capacitors fail in ways that drift with temperature. If it works when cold and fails when warm, or needs time to settle after power-up, suspect the capacitors first.

Hum on the audio and a washed-out picture are the two classic PC Engine capacitor symptoms. The hum comes from failed decoupling on the audio supply, and the weak picture comes from the same problem on the video rail. Both are the same fault showing up in two places.

Diagnosis

Confirming with ESR before you commit

Inspect the board. PC Engine capacitors do not always bulge, so a clean-looking board is not proof of a clean bill of health. Look for the dull, slightly domed appearance of a capacitor whose seal has begun to fail.

Measure ESR on a sample across the board. Take readings from the audio section, the video section and the main supply decoupling. If the sample shows high ESR, replace the whole set; a partial recap on a console this old is a waste of a teardown.

  1. Open the shell and inspect for bulged tops, domed bases, residue or a dull seal.
  2. Measure ESR on capacitors in the audio, video and supply sections and compare with the datasheet.
  3. Check the supply rails for ripple with the console running, which shows up the same fault from the other direction.
  4. Test the console cold and again after twenty minutes of running, and write down which symptoms change.
  5. Look for previous repair work, which tells you what someone else already tried.
  6. Check the voltage regulator output, since a failed regulator produces symptoms that look like a capacitor fault.
Remedy

Recapping the whole board

Replace every electrolytic capacitor on the board, using 105 °C parts. Note the polarity of each one before removal; the silkscreen on early PC Engine boards is not always reliable and there are documented errors, so photograph each position as you go.

Clean the board thoroughly with isopropyl alcohol when you are done and inspect every joint under a loupe. A recap introduces more solder joints than any other repair, so it introduces more opportunities for a cold joint, and a cold joint in the video section will produce exactly the symptom you were trying to fix.

  1. Photograph each capacitor position and record the value and polarity before removal.
  2. Desolder each capacitor, clearing the holes properly rather than forcing new leads through old solder.
  3. Fit 105 °C capacitors of the same capacitance and equal or higher voltage rating.
  4. Clean the board with isopropyl alcohol and inspect every joint under a loupe.
  5. Adjust the video output level if the board has a trimmer, using a test pattern on a known-good display.
  6. Test cold, then run for an hour and test again, comparing against the notes you took before the repair.

Fault tree branches

where this symptom also leads
BR

If: The recap is done and the picture is still weak

Check the video output stage and the trimmer, and confirm you have no cold joints in that section.

Super NES audio hum: the audio amp decoupling and the S-DSP
BR

If: The console will not power on at all, even cold

Check the regulator and the power input before assuming the recap failed.

Early PlayStation power supply: leaking capacitors that ate the board
BR

If: The console powers correctly but will not read cards

The fault is at the card slot rather than the supply.

PC Engine HuCard not reading: cleaning and tensioning the card slot